Hight Energy Ignition Systems

200 HEI 5AA BOX:

The Combustion and Energy ignitor rod cod. 200-HEF-5AA is suitable to be use with burners, furnaces, flares,…

It is made of stainless steel and it is avaible with 1/2″ connection connection pilot side. We can make ignitor rods with length on demand.

Connections at the end of the lance is one small Atex certified box to connect the cable.

As spare part it is available also only the spark tip (200-HEF-9A3).

200 HEP A6Z 7J

The 200-HEP-A6Z 7J HEI flare ignition module mountable on DIN connection with a power discharge of 7J. A booster function has been implemented (four 7J sparks are generated in one second).
Thanks to its power supply requirement (12VDC) it could be use also with a solar panel to ignite system without external power source. This module is microprocessor controlled and it is used also for diagnostic function. It is possible to have special customization programs and sparking sequence.
It could be use for ignite flares, stacks, boilers…
On the front of the module there is a screw that allow to set the discharge frequency: from less than 1 spark each 0,6s till 1 spark each 8s.
200-HEP-A6Z HEI flare ignition could be coupled with a dedicate MDR  power supply that allow to have a power supply from 100 to 240VAC.

200 HEP A6Z 2J

The 200-HEP-A6Z 2J HEI flare ignition module mountable on DIN connection with a power discharge of 2J. A booster function has been implemented (four 2J sparks are generated in one second).

Thanks to its power supply requirement (12VDC) it could be use also with a solar panel to ignite system without external power source. This module is microprocessor controlled and it is used also for diagnostic function. It is possible to have special customization programs and sparking sequence.

It could be use for ignite flares, stacks, boilers…

On the front of the module there is a screw that allow to set the discharge frequency: from less than 1 spark each 0,6s till 1 spark each 8s.

200-HEP-A6Z HEI flare ignition could be coupled with a dedicate MDR power supply that allow to have a power supply from 100 to 240VAC.

200 HEF 5AA

The Combustion and Energy ignitor rod cod. 200-HEF-5AA is suitable to be use with burners, furnaces, flares,…

It is made of stainless steel and it is available with 3/4″ NPT connection pilot side (1/2″ NPT as option). We can make ignitor rods with length on demand.

Quick connector to connect the probe to our flexible hose (200-HEF-90B).

As spare part it is available also only the spark tip (200-HEF-9A3).

200 HEF 90B

The Combustion and Energy flexible hoses 200-HEF-90B are made of external flexible in stainless steel material, suitable for installation in aggressive environment, on top of the flares, burners, furnaces…

Inside there a high temperature cable (mica cable) that it is suitable for high energy and high temperature.

At its end it has the connection for the ignitor rod 500-HEF-5AA.

200 HEP A6Z Ex:

The 200-HEP-A6Z EX FIX it is the fix application for in hazardous area of the high energy module 200-HEP-A6Z.

This module is used to ignite a number of oil/gas burners, and it could be installed on a frame support in hazardous area.

Each module is stand alone, indipendent and dedicate to it own ignitor: it is possible to have in one ATEX enclosure more than one module to ignite all the ignitors of one system.

High energy ignitor is suitable for igniting the heavier oils, particulary where gas is not available or permitted by regulations, or where a high degree of reliability is essential, e. g. for flare stacks, sulphur plants, or high pressure combustion chamber burners.

The enclosure is certified Ex d IIC IP65, and it is available with window on the top.

200 HEP A6Z Ex POR

The 200-HEP-A6Z EX POR it is used for portable application in hazardous area with our HE module.

A high energy portable ignition set is used to ignite a number of oil/gas burners, where the installation of a separate, permanent, high energy igniter on each boiler would be uneconomic and unpratical. High energy ignitor is suitable for igniting the heavier oils, particulary where gas is not available or permitted by regulations, or where a high degree of reliability is essential, e.g. for flare stacks, sulphur plants, or high pressure combustion chamber burners.

The enclosure is certified Ex d IIC IP65, and it is available with window on the top. The enclosure is certified with battery inside.

The item is complete with battery charger.

200 HEP A6Z IP

The 200-HEP-A6Z IP has the same caratheristic of the module 200-HEP-A6Z but in one IP65 enclosure.

This is a very small and good solution to have a ignition system ready to use.

Each module is dedicate to one ignitor: it is possible to have in one enclosure more than one module to ignite all the ignitors of one system.

High energy ignitor is suitable for igniting the heavier oils, particulary where gas is not available or permitted by regulations, or where a high degree of reliability is essential, e. g. for flare stacks, sulphur plants, or high pressure combustion chamber burners.

The box has a transparent cover that allow the check of status of module

Specifications:

The 225-HEF-A4Z module is a high energy module moutable on DIN bar, with a power discharge of 4J.

This module is feeded at 110VAC or 230VAC 50/60Hz and has a nominal operating voltage of 1kV.

It could be use for ignite flares, stacks, boilers…

 

Contact us for more information